# # INSTALL -- installation instructions # -------------- Installing mmh -------------- Please read all of the following instructions before you begin building mmh. You should check the MACHINES file to see if there are any specific build instructions for your operating system. To build mmh, you will need an ANSI C compiler such as gcc. 0) If you have obtained mmh by checking it out of git, you will need to run the GNU autotools to regenerate some files. (If your directory already contains a file 'config.h.in' then this has already been done and you do not need to do it.) You can regenerate the files by running the command ./autogen.sh (Note that if you're doing mmh development, you should look at docs/README.developers, since there is other developer-friendly advice there as well.) 1) From the top-level source directory, run the command: ./configure [options] This will check the configuration of your OS, as well as the various Makefiles. The configure script accepts various options. The options of most interest are listed in a section below. To see the list of all available options, you can run: ./configure --help 2) make 3) make install Note that if you have mmh files in your install directories with the same names as the files being installed, the old ones will get overwritten without any warning. The only directory this isn't true for, is the `etc' directory -- in that directory, the distributed files are installed with a `.dist' suffix if they differ from the existing file. Watch for information messages while make is processing that directory to see if you need to merge changes. 4) Edit the file `mhn.defaults' (installed in the mmh `etc' directory). This file contains the default profile entries for the mmh commands mhlist/mhstore/show. The syntax of this file is described in section 9.4 of the book "MH & xmh: Email for Users and Programmers", 3rd edition, by Jerry Peek, on the Internet at . 5) Add the bindir to your PATH variable. If you haven't change any paths, then the bindir is `/usr/local/mmh/bin'. Likely, your PATH is set in ~/.profile, ~/.kshrc, ~/.bashrc, or a similar file. ----------------------------------------------- Compiler options, or using a different compiler ----------------------------------------------- By default, configure will use the "gcc" compiler if found. You can use a different compiler, or add unusual options for compiling or linking that the "configure" script does not know about, by either editing the user configuration section of the top level Makefile (after running configure) or giving "configure" initial values for these in its command line or in its environment. For example: ./configure CC=c89 CFLAGS=-O2 LIBS=-lposix Or on systems that have the "env" program, you can do it like this: env CPPFLAGS=-I/usr/local/include LDFLAGS=-s ./configure If you want to add to, not replace, compile flags, you can use OURDEFS: ./configure OURDEFS='-Wextra -Wno-sign-compare' ---------------------------------------- Building mmh on additional architectures ---------------------------------------- To build mmh on additional architectures, you can do a "make distclean". This should restore the mmh source distribution back to its original state. You can then configure mmh as above on other architectures in which you wish to build mmh. Or alternatively, you can use a different build directory for each architecture. --------------------------------- Using a different build directory --------------------------------- You can compile the mmh in a different directory from the one containing the source code. Doing so allows you to compile it on more than one architecture at the same time. To do this, you must use a version of "make" that supports the "VPATH" variable, such as GNU "make". "cd" to the directory where you want the object files and executables to go and run the "configure" script. "configure" automatically checks for the source code in the directory that "configure" is in. For example, cd /usr/local/solaris/mmh /usr/local/src/mmh-1.0/configure make --------------------- Options for configure --------------------- --prefix=DIR (DEFAULT is /usr/local/mmh) This will change the base prefix for the installation location for the various parts of mmh. Unless overridden, mmh is installed in ${prefix}/bin, ${prefix}/etc, ${prefix}/lib, ${prefix}/man. --bindir=DIR (DEFAULT is ${prefix}/bin) mmh's binaries (show, inc, comp, ...) are installed here. You need to have this directory in your PATH variable. --libdir=DIR (DEFAULT is ${prefix}/lib) mmh's test tools (ap, dp, mhtest, ...) are installed here. They are seldom useful to normal users. --sysconfdir=DIR (DEFAULT is ${prefix}/etc) mmh's config files (mhn.defaults, ...) are installed here. --mandir=DIR (DEFAULT is ${prefix}/man) mmh's man pages are installed here. --enable-debug Enable debugging support. --with-locking=LOCKTYPE (DEFAULT is dot) Specify the locking mechanism when attempting to "inc" a local mail spool. Valid options are "dot", "fcntl", "flock", and "lockf". Of the four, dot-locking requires no special kernel or filesystem support, and simply creates a file called "FILE.lock" to indicate that "FILE" is locked. In order to be effective, you should contact the site administrator to find out what locking mechanisms other mail delivery and user programs respect. The most common reason not to use dot-locking is if the mail spool directory is not world- or user-writeable, and thus a lock file cannot be created. -- markus schnalke and the nmh team